DDC
  • Welcome
    • Introduction
    • Supported hardware
  • 1: Project planning
    • Switch inputs
      • Switch table
      • Direct
      • Shift register
      • Port expander
    • Analog inputs
      • External ADC
    • RGB LED
    • Digital outputs
    • PWM / Circuit control
    • EEPROM
    • Processing and memory
  • 2. Wiring
    • Switch inputs
      • Matrix
      • Direct
      • Shift register
      • Port expander
    • Analog
      • Analog switches
      • External ADC
    • RGB LED
    • Digital outputs
    • PWM / Circuit control
    • EEPROM
  • 3. Coding
    • Essentials
      • 02_Board.ino
      • 08_Joystick
      • 10_TableAndAnalog.ino
        • Switch table
        • Analog channels
      • 30_Switches.ino
    • Peripherals
      • RGB LED
        • Firmware control
          • LED functions
          • Color
          • Brightness
          • Presets
        • SimHub control
      • Digital outputs
        • Setup
        • SimHub control
        • Firmware control
      • PWM / Circuit control
        • Setup
        • Calibrate
        • Switch control
        • Trigger control
      • Shift register
      • I2C devices
        • ADS1115
        • PCA9555
        • CAT24C512
    • Advanced
      • Analog inject
      • Conditional coding
        • Triggers
        • Editors
      • Field placement
      • Presets
        • 31_RunningPresets.ino
        • 32_Presets.ino
        • Example
    • Upload
    • Naming the controller
  • 4. Connect to SimHub
    • LED control
    • Controller settings and properties
      • How to connect?
      • How does it work?
      • How to control it?
      • Property list
  • Switch library
    • Pushbutton
    • Function switches
    • Toggle switches
    • Hat switches
    • Car control functions
      • QuickSwitch
      • BrakeMagic
      • ThrottleHold
      • Handbrake
    • Pedals & paddles
      • Brake/throttle
      • Clutch
      • Bite point & launch
      • Filtered curves
      • Shifter
    • Funky switch
      • Directional
      • Center push
    • Encoders
      • rotary2Bit
      • rotary4Bit
      • funkyRotary
      • wildEncoder
      • E18
      • rotaryPulse
      • PEC11
    • Rotary switches
      • rotaryAnalog
      • quickRotary
      • SW1
      • Editing functions
    • Multiswitch complexes
      • Hybrid rotary
      • Multifunction rotary
      • Modded encoder
      • Stacked encoder
    • Preset
    • DDS
    • RGB LED control
    • PWM / Circuit control
    • Utility
  • Fast DDC
    • Buttons and LED
    • 4 encoders, buttons and LED
    • Dual clutches, 4 encoders, buttons and LED
    • Dual clutches, 6 encoders, button matrix and LED
  • CB1
    • Ordering
      • Order together
      • Order yourself
        • 1. Open in EasyEDA
        • 2. Export files
        • 3. Edit Pick&Place
        • 4. Pin headers and jumper
        • 5. Order from JLCPCB
    • Wiring
    • Code
      • Essentials
      • Complete project
      • Settings
    • Circuit
    • Shields
      • Robin
  • Collaboration
Powered by GitBook
On this page
  1. Fast DDC

Buttons and LED

PreviousFast DDCNext4 encoders, buttons and LED

Last updated 6 days ago

  • Hold button 1 and 2 together for 5 seconds to restart the controller and boot as storage device.

  • LEDs are running on 3.3V data in this diagram, which works up to a certain LED count. Limit is set to 30 because more is unlikely to work. For higher LED counts use a level shifter and set up a full DDC firmware.

173KB
B25_LED30.uf2